About us
Our Lvyuan Fliter always insists on product quality is life, our aim is to provide more professional and attentive cartridge filter, filter housing and services for our global customers.
Latest products
- water purifier filter installation and water quality requirements 【 3 m filter.
by：Lvyuan Filter
2021-01-25
Water purifier has gradually become household essentials, the filter is the core of the water purifier, water purifier filter installation is therefore each family needs to face, and depends not only on the quality of the filter water purifier water water quality requirements, more depends on whether the service life of filter element and get timely replacement.
To
water purifier filter installation (1) the water pressure is higher than 3 kg, shall be installed in the water pressure reducing valve.
(2) the total feed line is far away from the installation place needs to be installed ahead of product water inlet ball valve.
3. Split open a case to check for each level of the filter shell tapping is tight, if loose phenomenon should tighten in time, to prevent water penetration.
(4) the hollow filament membrane filter ( Level 4) In four filter, remove the activated carbon filter ( The secondary and tertiary) , rinse to no blackwater out first, then into the shell, preparations were made.
5. Select the location of the machine installation according to customer requirements, when electric hammer hole, drill bit should be small and large, its growing from small to big, so as not to damage the customer home decoration. Hole after good, gong expansion bolt into the same size, then the machine hang on tight.
6 for connection to the water, turn off the water valve always first, and then loaded on supporting tee, connected to two in charge of the inlet pipe, tighten the gong a mother can.
7) according to customer demand, choose the installation position of the tap, mount outlet connection pipe ( Binary) Can. The drainage pipe and outlet pipe synchronization is complete.
today if you want to pick up water dispenser need to install a tee in purifying water exports.
pet-name ruby of each product line connection according to product manuals.
water purifier water water quality requirements
1, water purifiers, generally must be under normal temperature water, can't go to hot water, so water filter must be installed in the front of the hot water boiler, heat device, and shall ensure that the installation position of water purifier is lower than the location of the water boiler, in order to prevent the water boiler steam into water purification machine, damage the filters filter.
2, water purification machines, all piping, joints, faucets and other wading accessories should comply with the national hygiene standards.
3, in the north do not installed in the outdoor, in order to prevent the frost crack super filter, at the same time, should avoid direct sunlight.
4, tighten the nipple when installation don't too hard, prevent joint thread tooth.
water purifier filter installation (1) the water pressure is higher than 3 kg, shall be installed in the water pressure reducing valve.
(2) the total feed line is far away from the installation place needs to be installed ahead of product water inlet ball valve.
3. Split open a case to check for each level of the filter shell tapping is tight, if loose phenomenon should tighten in time, to prevent water penetration.
(4) the hollow filament membrane filter ( Level 4) In four filter, remove the activated carbon filter ( The secondary and tertiary) , rinse to no blackwater out first, then into the shell, preparations were made.
5. Select the location of the machine installation according to customer requirements, when electric hammer hole, drill bit should be small and large, its growing from small to big, so as not to damage the customer home decoration. Hole after good, gong expansion bolt into the same size, then the machine hang on tight.
6 for connection to the water, turn off the water valve always first, and then loaded on supporting tee, connected to two in charge of the inlet pipe, tighten the gong a mother can.
7) according to customer demand, choose the installation position of the tap, mount outlet connection pipe ( Binary) Can. The drainage pipe and outlet pipe synchronization is complete.
today if you want to pick up water dispenser need to install a tee in purifying water exports.
pet-name ruby of each product line connection according to product manuals.
water purifier water water quality requirements
1, water purifiers, generally must be under normal temperature water, can't go to hot water, so water filter must be installed in the front of the hot water boiler, heat device, and shall ensure that the installation position of water purifier is lower than the location of the water boiler, in order to prevent the water boiler steam into water purification machine, damage the filters filter.
2, water purification machines, all piping, joints, faucets and other wading accessories should comply with the national hygiene standards.
3, in the north do not installed in the outdoor, in order to prevent the frost crack super filter, at the same time, should avoid direct sunlight.
4, tighten the nipple when installation don't too hard, prevent joint thread tooth.
Custom message
