Automatic softening water equipment maintenance and operation standard

Water softener is more common in the life of equipment, it can reduce the water hardness, it includes tanks, generally for the stainless steel or glass fiber reinforced plastic, control valves, vacuum salt boxes, regeneration system, and operation of pipeline. At the time of use may be according to their willingness to pay attention to use, but we seldom notice while using the way we use is correct, even bad consequences, to shorten the service life of softened water equipment, and varying degrees of damage.

　　1. Maintain equipment daily cleaning is cannot little, refueling part keep sufficient oil supply, runtime careful not to touch the pulley, thus can avoid the happening of the accident.

　　2. If equipment downtime for more than half a month, nylon pipe waste water up to exchange column, make it undrained, long-term need not when dealing with salt shaker and the rest of the body salt liquid for cleaning. The transmission part and the rotary valve and add lubricating oil, it is strictly prohibited devices induced, summer and mildew season down more than half, should start the machine 60 to 120 minutes, in case the resin tank microbes will grow on it. Restarts, flipping the pulley by hand, and several times to rotate the rotary valve, put the water in the original position after the electricity.

　　3. Equipment is in place, will be fixed motor, limit switch of the bolt, switchboard connection bolt, and then to a fixed inside and outside, so as to avoid accidents during operation. Rotary valve on the pull rod fixed block up and down bolts shall be fixed well, try to avoid exchange column has a collision happens.

　　4. The device is working, don't relay to adjust in time. Scrub in but after power off to repair equipment, to fundamentally prevent motor, switchboard, limit switch failure occurs in the water. At the same time in the operation, power supply, water supply shutdown, close all of water power. Each time the user downtime, should not stop in a short period, should stop water supply at the same time.

　　【 The standardization of automatic soft water equipment process 】

work ( Sometimes called water production, hereinafter the same) , backwashing, suck salt ( Regeneration) Flushing, slow ( Replacement) , quick wash five process. All the working procedure is very close to different softening water equipment, just due to the needs of different or control of actual process, there may be some additional process. Any based on sodium ion exchange softening water equipment is on the basis of the five process development ( Among them, the automatic softening water equipment can increase the brine refill process) 。

automatic soft water equipment standard 4 don't walk:

demineralized water equipment working procedures:

backwashing: equipment work after a period of time, in the upper portion resin intercept many contaminants from raw water, remove the dirt, after ion exchange resin can be completely exposed, the effect of regeneration can be guaranteed. Backwashing process is to wash the into the water from the bottom of the resin flow from the top, so can put at the top of the intercept down and wash away dirt. Usually need to 5 - the process About 15 minutes.

demineralized water equipment working procedure 2:

salt ( Regeneration) : is the process of brine is injected resin tanks, traditional equipment is to use salt will salt water injection pump, automatic equipment is a special built-in injector will salt water suction ( As long as there is a certain water pressure) 。 In the process of practical work, saline at a slower speed through the resin regeneration effect than pure use saline soak resin effect is good, so the filter source automatic softening water equipment are adopt the method of brine is slowly through the resin regeneration, this process generally takes about 30 minutes, actual time leaves the effects of salt.

demineralized water equipment work program three:

slow flushing ( Replacement) : after through the resin with brine, will slowly with the raw water with the same velocity of resin rinse clean all the salt washing process is slower, because this flushing process there are still a lot of calcium and magnesium ions on the functional groups by sodium ion exchange, according to the practical experience, the process is the main process of regeneration, so a lot of people will this process is called substitution. This process is generally with salt absorption at the same time, namely, about 30 minutes. - - - Demineralized water equipment

demineralized water equipment work program:

automatic softening water equipment quick rinse, rinse thoroughly, in order to bring the remaining salt to use close to the actual work flow, with the raw water to flush of resin, the final effluent of this process shall be the standard of soft water. In general, fast for 5 - flushing process 15 minutes.