Automatic softening water equipment selection and installation debugging

My company is softened water equipment, water softener manufacturers, water softener is commonly used in water treatment processing equipment, widely used in steam boiler, hot water boiler, switches, evaporative condenser, air conditioning, direct-fired machine system such as make-up water softening. Can also be used in hotels, restaurants, office buildings, apartment, home life such as water treatment and food, beverage, wine, laundry, printing and dyeing, chemical, pharmaceutical and other industries to soften water treatment. So a demineralized water, how to use?

1。 Raw water quality conditions shall conform to the requirements of general sodium ion exchange water treatment equipment.

2。 Equipment installation indoors, to prevent corrosion resin freezing and parts, electrical short circuit fault, environmental temperature should be above zero, and no steam, dry and clean place.

3。 After equipment is in place, for all the retaining bolt, especially fixed motor bolt connection bolt, limit switch and panel inside and outside should be retightened again, panel shell connected to.

4。 Rotary valve on the pull rod fixed block up and down bolt looseness, exchange column can not hit.

5。 Don't adjust time relay, work, scrubbing equipment maintenance, must cut off power supply, and to prevent motor, switchboard, limit switch, into the water.

6。 Suspended operation, power supply, water supply at the same time, also hydropower shut.

7。 Often keep the equipment clean, refueling part don't lack of oil, the runtime careful not to touch the belt pulley, so as to avoid an accident.

8。 Nylon pipe equipment downtime for more than half a month, waste water up to exchange column, make it undrained, long-term need not when dealing with salt shaker and the rest of the body salt liquid for cleaning. The transmission part and the rotary valve and add lubricating oil, it is strictly prohibited devices induced, summer and mildew season down more than half, should start the machine one or two hours, in case the resin tank microbes will grow on it. Restarts, flipping the pulley by hand, and several times to rotate the rotary valve, then the electricity, the drain back in situ.

9。 Equipment maintenance once a year, salt scrub brush paint cans looks up and down bottom protection, the exchange column should check the resin layer height, uncovered the flange on the equipment of the resin filling rate ( Resin layer/exchange column high x %) 85% - Should be added 90%, not enough, in other circumstances for maintenance.

10。 Panel and equipment body has been shipped together, if the unit using the conditional, but the panel with the separation of ontology. Switchboard and hung in a fixed place, but the connection number cannot be wrong.

11。 Each time the user downtime, should not stop in a short period, should stop water supply at the same time.

12. For water quality, the larger sediment loads before softening precipitation and then into the machine.

2, softened water equipment installation notice:

1, this device must be placed in the interior, to prevent frostbite, sunscreen, moves must prevent collision.

2, when installation, should be around zero. 5 meters gap, in order to maintenance.

3, feed water pressure at 0. 3 - 0. Between 4 mpa, such as can not satisfy can increase the pressure relief measures.

4, users should the mixed softened water tank, the volume should be according to usage, in order to meet the water requirement, the soft water tank should be anticorrosive measures, in case of soft water pollution again.

5, do not need to do to install base, which can be installed at the foundation level require drainage channels near the ground.

6, keep saturated salt liquid concentration, solid salt liquid level should be higher than the salt.

7, after the installation should be flush pipe, in order to prevent the impurities clogging up resin and pollution.

we provide softened water equipment, automatic demineralized water control valves, boiler softened water equipment, rich lake FLECK control valves, softened water equipment, softened water equipment maintenance, reverse osmosis equipment. The equipment are of good quality and easy installation.

3, my company production of water softener advantage analysis

1, the new material softening resin, exchange rate is high, long service life.

2, using the American brand softening controller, reliable in performance.

3, in and out of the mouth, a free demolition controller can change the filter material.

4, fine workmanship, polishing, such as a mirror, class is high.

5, debugging personnel have many years of experience in installation and debugging, can put forward reasonable scientific advice.

6, after-sales service in a timely manner, 24 hours to respond.